HFSS9 Getting Started.pdf

bitbadboy

【文件名】:06112@52RD_HFSS9 Getting Started.pdf
【格　式】:pdf
【大　小】:3600K
【简　介】:hfss使用入门
【目　录】:
1. Introduction
About the T-Junction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Expected Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Using HFSS 9.0 to Create and Improve the Design . . . . . 1-3
2. Set up the Design
Open HFSS and Save a New Project . . . . . . . . . . . . . . . . 2-2
Insert an HFSS Design . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Select a Solution Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Set the Drawing Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
3. Create the Model
Create the T-Junction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Draw a Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Assign a Name to the Box . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Confirm the Material Assigned to the Box . . . . . . . . . . . . . 3-4
Increase the Transparency of the Box . . . . . . . . . . . . . . . 3-4
Assign a Wave Port to the Box . . . . . . . . . . . . . . . . . . . . . 3-5
Duplicate the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Set Duplicates to Copy Boundaries . . . . . . . . . . . . . . . . . 3-6
Duplicate the Box to Create the Second Section . . . . . . 3-6
Duplicate the Box to Create the Third Section . . . . . . . . . 3-8
http://www.mweda.com ——ADS, HFSS, Ansoft Designer培训教程网站
Getting Started with Optimetrics: A Waveguide T-Junction
Contents-2
Unite the Boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Create the Septum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Draw a Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Parameterize the Position of the Box . . . . . . . . . . . . . . . . 3-11
Modify the Dimensions of the Box . . . . . . . . . . . . . . . . . . . 3-11
Assign a Name to the Box . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Subtract the Septum from the T-Junction . . . . . . . . . . . . . 3-13
4. Set up and Generate Solutions
Add a Solution Setup to the Design . . . . . . . . . . . . . . . . . . 4-2
Add a Frequency Sweep to the Solution Setup . . . . . . . . 4-2
Validate the Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Analyze the Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Move the Position of the Septum . . . . . . . . . . . . . . . . . . . . 4-5
Re-analyze the Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
5. Compare the Solutions
Create a Rectangular Plot of S-Parameter Results . . . . . 5-2
Create a Field Overlay Plot . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Modify the Position of the Septum . . . . . . . . . . . . . . . . . . 5-4
Create the Field Plot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Animate the Field Overlay Plot . . . . . . . . . . . . . . . . . . . . . 5-6
Modify the Septum’s Position and Re-animate . . . . . . . . . 5-7
Close the Project and Exit HFSS . . . . . . . . . . . . . . . . . . . . 5-8