校准难题请教,请赐教!!

searover

校准MTK6225平台,为什么在最后加载6225的setup文件重新启动后,会提示:MediaTec Inc.. 遇到问题需要关闭",然后就关掉了,用的ATETOOL 5.3.8版本,又试着用别的版本也会出现此问题,加载6229的可以,但是APC都过不了，真的是奇怪,请高手赐教!!

jiangxu520

SETUP文件有问题，换此文件应该可以！

skb2008

安装文件有问题，APC是你其它文件或板的问题[em01][em01][em01]

121348581

Spectrum due to switching enable = "1,0,0,1,"
Spectrum due to modulation enable = "0,0,0,1,1,0,0,1,0,0,1,"
GSM850 ORFS_SW = "-19.0,-19.0,-21.0,-21.0,-21.0,-21.0,-24.0,-24.0,"
GSM900 ORFS_SW = "-19.0,-19.0,-21.0,-21.0,-21.0,-21.0,-24.0,-24.0,"
DCS1800 ORFS_SW = "-15.0,-15.0,-21.0,-21.0,-21.0,-21.0,-24.0,-24.0,"
PCS1900 ORFS_SW = "-19.0,-19.0,-21.0,-21.0,-21.0,-21.0,-24.0,-24.0,"
GSM850 ORFS_MOD Line0001 = "0.5,0.5,-30.0,-30.0,-33.0,-33.0,-55.0,-55.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,"
GSM850 ORFS_MOD Line0002 = "-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,"
GSM900 ORFS_MOD Line0001 = "0.5,0.5,-30.0,-30.0,-33.0,-33.0,-55.0,-55.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,"
GSM900 ORFS_MOD Line0002 = "-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,"
DCS1800 ORFS_MOD Line0001 = "0.5,0.5,-30.0,-30.0,-33.0,-33.0,-50.0,-50.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,"
DCS1800 ORFS_MOD Line0002 = "-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,"
PCS1900 ORFS_MOD Line0001 = "0.5,0.5,-30.0,-30.0,-33.0,-33.0,-55.0,-55.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,"
PCS1900 ORFS_MOD Line0002 = "-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,"
EGSM850 ORFS_SW = "-19.0,-19.0,-21.0,-21.0,-21.0,-21.0,-24.0,-24.0,"
EGSM900 ORFS_SW = "-19.0,-19.0,-21.0,-21.0,-21.0,-21.0,-24.0,-24.0,"
EDCS1800 ORFS_SW = "-19.0,-19.0,-21.0,-21.0,-21.0,-21.0,-24.0,-24.0,"
EPCS1900 ORFS_SW = "-19.0,-19.0,-21.0,-21.0,-21.0,-21.0,-24.0,-24.0,"
EGSM850 ORFS_MOD Line0001 = "0.5,0.5,-30.0,-30.0,-33.0,-33.0,-55.0,-55.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,"
EGSM850 ORFS_MOD Line0002 = "-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,"
EGSM900 ORFS_MOD Line0001 = "0.5,0.5,-30.0,-30.0,-33.0,-33.0,-55.0,-55.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,"
EGSM900 ORFS_MOD Line0002 = "-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,"
EDCS1800 ORFS_MOD Line0001 = "0.5,0.5,-30.0,-30.0,-33.0,-33.0,-55.0,-55.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,"
EDCS1800 ORFS_MOD Line0002 = "-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,"
EPCS1900 ORFS_MOD Line0001 = "0.5,0.5,-30.0,-30.0,-33.0,-33.0,-55.0,-55.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,"
EPCS1900 ORFS_MOD Line0002 = "-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,"
WT4400 Coupling Loss = "801.0,0.6,1701.0,1.2,999.0,0.8,1999.0,1.3"


把你用的那版本里面默认的SETUP上面一段复制到你现在用的这个SETUP，覆盖掉就OK了

jiangxifzy

[em13][em13]

15919707670

[em07]