推荐好书:EMI FILTER DESIGN Second Edition

yantaisgj

非常清晰!全英文!
目录:
1. Why Call EMI Filters Black Magic?
2. Common and Differential Mode—Definition, Cause, and Elimination
3. EMI Filter Source Impedance of Various Power Lines
4. The Various AC Load Impedances
5. DC Circuit—Load and Source
6. Typical EMI Filters—Pros and Cons
7. Filter Components—The Capacitor
8. Filter Components—The Inductor
9. Common Mode Components
10. The Transformer’s Addition to the Filter
11. Electromagnetic Pulse and Voltage Transients
12. What Will Compromise the Filter?
13. Waves as Noise Sources
14. Study of the Off-line Regulator
15. Initial Filter Design Requirements
16. Matrices—Review of A Matrices
17. The Filter Design Technique
18. Matrix Applications
19. Applications Using Round or Square Conducting Rods
20. Packaging Information
21. Design Examples
22. Questionable Designs
23. Review of Filter Design

yantaisgj

网络出错......
明天再传!

yantaisgj

【文件名】:08221@52RD_EMI FILTER DESIGN(1).rar
【格　式】:rar
【大　小】:2733K
【简　介】:
【目　录】:

[此贴子已经被作者于2008-2-22 8:19:20编辑过]

yantaisgj

<P>ding</P>[em08]

[此贴子已经被作者于2008-2-22 8:35:15编辑过]

yantaisgj

[em08][em08][em08]

[此贴子已经被作者于2008-2-22 8:35:46编辑过]

Noise

[em02][em02][em02]谢谢楼主分享。。。[em08][em08]

yantaisgj

[em09][em09][em09][em09]

steveniyang

ding.

txjxj

xiexie

john019

Why Call EMI Filters Black Magic?
Most engineers, both designers of electromagnetic interference (EMI) devices and
others, call EMI black magic. There are four main reasons for this. First, there
has not been a well-defined design method. Second, the input and output
impedances are not constant over the band of interest. The impedances are usually
just good guesses, at best, because the measurements are costly to make and are
rarely repeatable. Third, the filter insertion loss test method specifications often
confuse or influence the design method. In the 220A specification, requiring
50-ohm source and load impedances, does the filter engineer design the filter for
the 50 ohms or for real-world impedances? If the design passes the Military
Standard (MIL STD) 220A, 50-ohm, test, what will happen in the real world? Is it
the designer’s responsibility to meet the specification or to stop the real-world
emissions? Fourth, the design methods outlined in various publications are
generally very complex. Most require measurements that are difficult to make and
time consuming. Often expensive additional equipment is required to obtain the
needed parameters.
1.1. WHAT IS EMI?
EMI is electromagnetic interference and is called conducted emissions or radiated
emissions. This book covers mainly conducted emissions (CEs), which means any
unwanted signal or noise on the wiring or copper. The reason for the reference to
power cabling is that EMI filters are part of the power wiring and are designed
to remove these unwanted properties from the copper wiring. Why is this from
the wiring? What does this have to do with magnetic fields? The reason is that
Copyright &copy;...............

yiranzaifei

谢谢你

lishangyu

顶之  色色

saul32

好楼主！！！！！！

pwzh

ziliao bucuo  kaning

xiaotian28

thanks a lot for your sharing

tandyok

thanks ,you are so fine

lxd07992

很不错的资料，还是老外靠谱