Recommended Minimum Performance Standards

ouyqq

1 NORMATIVE REFERENCES..........................................................................................xxxix
2 1 INTRODUCTION.........................................................................................................1-1
3 1.1 Scope....................................................................................................................1-1
4 1.2 Terms and Definitions..........................................................................................1-1
5 1.3 Test Modes .........................................................................................................1-15
6 1.4 CDMA Equations................................................................................................1-16
7 1.4.1 Transmit Power of the Base Station .............................................................1-16
8 1.4.2 Received Signal Strength for Mobile Station Not in Handoff ........................1-17
9 1.4.2.1 Single-Path Case ....................................................................................1-17
10 1.4.2.2 Two-Path Case ........................................................................................1-18
11 1.4.2.3 Three-Path Case .....................................................................................1-19
12 1.4.3 Received Signal Strength for Mobile Station in Two-Way Handoff ...............1-19
13 1.5 Tolerances..........................................................................................................1-20
14 1.5.1 CDMA System Parameter Tolerances ...........................................................1-20
15 1.5.2 Measurement Tolerances .............................................................................1-20
16 1.6 Test Requirements for Mobile Stations Supporting Analog Operation...............1-20
17 1.6.1 Modulated Tone Frequency..........................................................................1-20
18 2 STANDARD RADIATED EMISSIONS MEASUREMENT PROCEDURE.........................2-1
19 2.1 Standard Radiation Test Site ...............................................................................2-1
20 2.2 Search Antenna ...................................................................................................2-1
21 2.3 Field-Strength Measurement ...............................................................................2-2
22 2.4 Frequency Range of Measurements .....................................................................2-2
23 2.5 Test Ranges..........................................................................................................2-2
24 2.5.1 30-Meter Test Range ......................................................................................2-2
25 2.5.2 3-Meter Test Range ........................................................................................2-3
26 2.6 Radiated Signal Measurement Procedures ..........................................................2-3
27 3 CDMA RECEIVER MINIMUM STANDARDS................................................................3-1
28 3.1 Frequency Coverage Requirements......................................................................3-1
29 3.1.1 Band Class 0 (800 MHz Band)........................................................................3-1
30 3.1.2 Band Class 1 (1900 MHz Band)......................................................................3-5
31 3.1.3 Band Class 2 (TACS Band) .............................................................................3-9
3GPP2 C.S0011-B
CONTENTS
ii
3.1.4 Band Class 1 3 (JTACS Band) ......................................................................... 3-13
2 3.1.5 Band Class 4 (Korean PCS Band)................................................................. 3-15
3 3.1.6 Band Class 5 (450 MHz Band) ..................................................................... 3-17
4 3.1.7 Band Class 6 (2 GHz Band) .......................................................................... 3-21
5 3.1.8 Band Class 7 (700 MHz Band) ..................................................................... 3-22
6 3.1.9 Band Class 8 (1800 MHz Band) ................................................................... 3-24
7 3.1.10 Band Class 9 (900 MHz Band) ..................................................................... 3-26
8 3.1.11 Band Class 10 (Secondary 800 MHz Band) .................................................. 3-27
9 3.1.12 Band Class 11 (400 MHz European PAMR Band) ........................................ 3-31
10 3.1.13 Band Class 12 (800 MHz PAMR Band) ......................................................... 3-34
11 3.2 Acquisition Requirements.................................................................................. 3-36
12 3.2.1 Idle Handoff Tests ........................................................................................ 3-36
13 3.2.1.1 Idle Handoff in Non-Slotted Mode on the Paging Channel ..................... 3-36
14 3.2.1.1.1 Definition ........................................................................................... 3-37
15 3.2.1.1.2 Method of Measurement .................................................................... 3-37
16 3.2.1.1.3 Minimum Standard............................................................................ 3-39
17 3.2.1.2 Idle Handoff in Slotted Mode on the Paging Channel............................. 3-39
18 3.2.1.2.1 Definition ........................................................................................... 3-40
19 3.2.1.2.2 Method of Measurement .................................................................... 3-40
20 3.2.1.2.3 Minimum Standard............................................................................ 3-41
21 3.2.1.3 Idle Handoff in Slotted Mode on the Forward Common Control
22 Channel.................................................................................................. 3-41
23 3.2.1.3.1 Definition ........................................................................................... 3-42
24 3.2.1.3.2 Method of Measurement .................................................................... 3-42
25 3.2.1.3.3 Minimum Standard............................................................................ 3-44
26 3.2.1.4 Idle Handoff to Another Frequency ........................................................ 3-44
27 3.2.1.4.1 Definition ........................................................................................... 3-44
28 3.2.1.4.2 Method of Measurement .................................................................... 3-44
29 3.2.1.4.3 Minimum Standard............................................................................ 3-50
30 3.2.2 Soft Handoff Tests ........................................................................................ 3-50
31 3.2.2.1 Neighbor Set Pilot Detection and Incorrect Detection in Soft
32 Handoff................................................................................................... 3-50
3GPP2 C.S0011-B
CONTENTS
iii
3.2.2.1.1 1 Definition ...........................................................................................3-50
2 3.2.2.1.2 Method of Measurement ....................................................................3-50
3 3.2.2.1.3 Minimum Standard ............................................................................3-53
4 3.2.2.2 Candidate Set Pilot Detection and Incorrect Detection in Soft
5 Handoff ...................................................................................................3-54
6 3.2.2.2.1 Definition ...........................................................................................3-54
7 3.2.2.2.2 Method of Measurement ....................................................................3-54
8 3.2.2.2.3 Minimum Standard ............................................................................3-57
9 3.2.2.3 Active Set Pilot Loss Detection in Soft Handoff ......................................3-57
10 3.2.2.3.1 Definition ...........................................................................................3-57
11 3.2.2.3.2 Method of Measurement ....................................................................3-58
12 3.2.2.3.3 Minimum Standard ............................................................................3-60
13 3.2.3 Access and Access Probe Handoff Tests.......................................................3-60
14 3.2.3.1 Access Probe Handoff .............................................................................3-60
15 3.2.3.1.1 Definition ...........................................................................................3-60
16 3.2.3.1.2 Method of Measurement ....................................................................3-61
17 3.2.3.1.3 Minimum Standard ............................................................................3-63
18 3.2.3.2 Access Handoff .......................................................................................3-64
19 3.2.3.2.1 Definition ...........................................................................................3-64
20 3.2.3.2.2 Method of Measurement ....................................................................3-64
21 3.2.3.2.3 Minimum Standard ............................................................................3-66
22 3.2.4 Candidate Frequency Single Search ............................................................3-67
23 3.2.4.1 Definition................................................................................................3-67
24 3.2.4.2 Method of Measurement.........................................................................3-67
25 3.2.4.3 Minimum Standard ................................................................................3-69
26 3.3 Forward Common Channel Demodulation Performance....................................3-69
27 3.3.1 Demodulation of Non-Slotted Mode Paging Channel ...................................3-69
28 3.3.1.1 Definition................................................................................................3-69
29 3.3.1.2 Method of Measurement.........................................................................3-70
30 3.3.1.3 Minimum Standard ................................................................................3-70
31 3.3.2 Demodulation of Slotted Mode Paging Channel ...........................................3-71
32 3.3.2.1 Definition................................................................................................3-71
3GPP2 C.S0011-B
CONTENTS
iv
3.3.2.2 Method 1 of Measurement......................................................................... 3-71
2 3.3.2.3 Minimum Standard ................................................................................ 3-72
3 3.3.3 Demodulation of Broadcast Control Channel in AWGN Channel ................ 3-73
4 3.3.3.1 Definition ............................................................................................... 3-73
5 3.3.3.2 Method of Measurement......................................................................... 3-73
6 3.3.3.3 Minimum Standard ................................................................................ 3-74
7 3.3.4 Demodulation of Broadcast Control Channel in Multipath Fading
8 Channel........................................................................................................ 3-74
9 3.3.4.1 Definition ............................................................................................... 3-74
10 3.3.4.2 Method of Measurement......................................................................... 3-74
11 3.3.4.3 Minimum Standard ................................................................................ 3-75
12 3.3.5 Demodulation of Forward Common Control Channel .................................. 3-76
13 3.3.5.1 Definition ............................................................................................... 3-76
14 3.3.5.2 Method of Measurement......................................................................... 3-76
15 3.3.5.3 Minimum Standard ................................................................................ 3-76
16 3.3.6 Demodulation of Common Assignment Channel and Reception of
17 Common Power Control Channel ................................................................. 3-77
18 3.3.6.1 Definition ............................................................................................... 3-77
19 3.3.6.2 Method of Measurement......................................................................... 3-77
20 3.3.6.3 Minimum Standard ................................................................................ 3-78
21 3.4 Forward Traffic Channel Demodulation Performance ........................................ 3-80
22 3.4.1 Demodulation of Forward Fundamental Channel in Additive White
23 Gaussian Noise ............................................................................................ 3-80
24 3.4.1.1 Definition ............................................................................................... 3-80
25 3.4.1.2 Method of Measurement......................................................................... 3-80
26 3.4.1.3 Minimum Standard ................................................................................ 3-81
27 3.4.2 Demodulation of Forward Fundamental Channel in Multipath Fading
28 Channel........................................................................................................ 3-81
29 3.4.2.1 Definition ............................................................................................... 3-81
30 3.4.2.2 Method of Measurement......................................................................... 3-82
31 3.4.2.3 Minimum Standard ................................................................................ 3-82
32 3.4.3 Demodulation of Forward Fundamental Channel During Soft Handoff ....... 3-83
3GPP2 C.S0011-B
CONTENTS
v
3.4.3.1 1 Definition................................................................................................3-83
2 3.4.3.2 Method of Measurement.........................................................................3-83
3 3.4.3.3 Minimum Standard ................................................................................3-84
4 3.4.4 Decision of Power Control Bit for Channels Belonging to Different Power
5 Control Sets During Soft Handoff.................................................................3-84
6 3.4.4.1 Definition................................................................................................3-84
7 3.4.4.2 Method of Measurement.........................................................................3-84
8 3.4.4.3 Minimum Standard ................................................................................3-86
9 3.4.5 Decision of Power Control Bit for Channels Belonging to the Same Power
10 Control Set ...................................................................................................3-86
11 3.4.5.1 Definition................................................................................................3-86
12 3.4.5.2 Method of Measurement.........................................................................3-86
13 3.4.5.3 Minimum Standard ................................................................................3-87
14 3.4.6 Demodulation of Power Control Subchannel During Soft Handoff ..............3-88
15 3.4.6.1 Definition................................................................................................3-88
16 3.4.6.2 Method of Measurement.........................................................................3-88
17 3.4.6.3 Minimum Standard ................................................................................3-89
18 3.4.7 Demodulation of Forward Traffic Channel in Multipath Fading Channel
19 with Closed Loop Power Control (FPC_MODE = ‘000’)..................................3-90
20 3.4.7.1 Definition................................................................................................3-90
21 3.4.7.2 Method of Measurement.........................................................................3-90
22 3.4.7.3 Minimum Standard ................................................................................3-91
23 3.4.8 Demodulation of Forward Traffic Channel in Multipath Fading Channel
24 with Closed Loop Power Control (FPC_MODE = ‘010’)..................................3-91
25 3.4.8.1 Definition................................................................................................3-91
26 3.4.8.2 Method of Measurement.........................................................................3-92
27 3.4.8.3 Minimum Standard ................................................................................3-93
28 3.4.9 Demodulation of Forward Traffic Channel in Multipath Fading Channel
29 with Outer Loop Power Control and Closed Loop Power Control
30 (FPC_MODE = ‘000’, ‘001’ and ‘010’).............................................................3-93
31 3.4.9.1 Definition................................................................................................3-93
32 3.4.9.2 Method of Measurement.........................................................................3-93
33 3.4.9.3 Minimum Standard ................................................................................3-94
3GPP2 C.S0011-B
CONTENTS
vi
3.4.10 Demodulation of Forward Traffic 1 Channel in Multipath Fading Channel
2 with Closed Loop Power Control (FPC_MODE = ‘000’) and Transmit
3 Diversity (OTD or STS) ................................................................................. 3-94
4 3.4.10.1 Definition ............................................................................................... 3-95
5 3.4.10.2 Method of Measurement......................................................................... 3-95
6 3.4.10.3 Minimum Standard ................................................................................ 3-96
7 3.4.11 Demodulation of Forward Traffic Channel in Multipath Fading Channel
8 with Closed Loop Power Control (FPC_MODE = ‘010’) and Transmit
9 Diversity (OTD or STS) ................................................................................. 3-96
10 3.4.11.1 Definition ............................................................................................... 3-96
11 3.4.11.2 Method of Measurement......................................................................... 3-96
12 3.4.11.3 Minimum Standard ................................................................................ 3-97
13 3.4.12 Demodulation of Power Control Subchannel During Reverse Pilot
14 Channel Gating............................................................................................ 3-98
15 3.4.12.1 Definition ............................................................................................... 3-98
16 3.4.12.2 Method of Measurement......................................................................... 3-98
17 3.4.12.3 Minimum Standard ................................................................................ 3-98
18 3.4.13 Demodulation of Power Control Subchannel During Reverse
19 Fundamental Channel Gating...................................................................... 3-99
20 3.4.13.1 Definition ............................................................................................... 3-99
21 3.4.13.2 Method of Measurement......................................................................... 3-99
22 3.4.13.3 Minimum Standard ................................................................................ 3-99
23 3.5 Receiver Performance....................................................................................... 3-100
24 3.5.1 Receiver Sensitivity and Dynamic Range ................................................... 3-100
25 3.5.1.1 Definition ............................................................................................. 3-100
26 3.5.1.2 Method of Measurement....................................................................... 3-100
27 3.5.1.3 Minimum Standard .............................................................................. 3-101
28 3.5.2 Single Tone Desensitization....................................................................... 3-101
29 3.5.2.1 Definition ............................................................................................. 3-101
30 3.5.2.2 Method of Measurement....................................................................... 3-101
31 3.5.2.3 Minimum Standard .............................................................................. 3-104
32 3.5.3 Intermodulation Spurious Response Attenuation ..................................... 3-104
33 3.5.3.1 Definition ............................................................................................. 3-104
3GPP2 C.S0011-B
CONTENTS
vii
3.5.3.2 Method 1 of Measurement.......................................................................3-104
2 3.5.3.3 Minimum Standard ..............................................................................3-108
3 3.5.4 Adjacent Channel Selectivity......................................................................3-108
4 3.5.4.1 Definition..............................................................................................3-108
5 3.5.4.2 Method of Measurement.......................................................................3-109
6 3.5.4.3 Minimum Standard ..............................................................................3-110
7 3.5.5 Receiver Blocking Characteristics ..............................................................3-110
8 3.5.5.1 Definition..............................................................................................3-111
9 3.5.5.2 Method of Measurement.......................................................................3-111
10 3.5.5.3 Minimum Standard ..............................................................................3-113
11 3.6 Limitations on Emissions.................................................................................3-113
12 3.6.1 Conducted Spurious Emissions .................................................................3-113
13 3.6.1.1 Definition..............................................................................................3-113
14 3.6.1.2 Method of Measurement.......................................................................3-113
15 3.6.1.3 Minimum Standard ..............................................................................3-113
16 3.6.2 Radiated Spurious Emissions ....................................................................3-114
17 3.6.2.1 Definition..............................................................................................3-114
18 3.6.2.2 Method of Measurement.......................................................................3-114
19 3.6.2.3 Minimum Standard ..............................................................................3-114
20 3.7 Supervision ......................................................................................................3-115
21 3.7.1 Paging Channel or Forward Common Control Channel .............................3-115
22 3.7.1.1 Definition..............................................................................................3-115
23 3.7.1.2 Method of Measurement.......................................................................3-116
24 3.7.1.3 Minimum Standard ..............................................................................3-118
25 3.7.2 Forward Traffic Channel .............................................................................3-118
26 3.7.2.1 Definition..............................................................................................3-118
27 3.7.2.2 Method of Measurement.......................................................................3-119
28 3.7.2.3 Minimum Standard ..............................................................................3-120
29 4 CDMA TRANSMITTER MINIMUM STANDARDS .........................................................4-1
30 4.1 Frequency Accuracy.............................................................................................4-1
31 4.1.1 Definition .......................................................................................................4-1
3GPP2 C.S0011-B
CONTENTS
viii
4.1.2 Method 1 of Measurement ................................................................................ 4-1
2 4.1.3 Minimum Standard ........................................................................................ 4-1
3 4.2 Handoff ................................................................................................................ 4-2
4 4.2.1 CDMA to CDMA Hard Handoff ....................................................................... 4-2
5 4.2.1.1 Definition ................................................................................................. 4-2
6 4.2.1.2 Method of Measurement........................................................................... 4-2
7 4.2.1.3 Minimum Standard .................................................................................. 4-3
8 4.2.2 Transmit Power after Hard Handoff................................................................ 4-3
9 4.2.2.1 Definition ................................................................................................. 4-3
10 4.2.2.2 Method of Measurement........................................................................... 4-5
11 4.2.2.3 Minimum Standard .................................................................................. 4-7
12 4.3 Modulation Requirements ................................................................................... 4-8
13 4.3.1 Time Reference............................................................................................... 4-8
14 4.3.1.1 Definition ................................................................................................. 4-8
15 4.3.1.2 Method of Measurement........................................................................... 4-8
16 4.3.1.3 Minimum Standard ................................................................................ 4-10
17 4.3.2 Reverse Pilot Channel to Code Channel Time Tolerance ............................. 4-10
18 4.3.2.1 Definition ............................................................................................... 4-10
19 4.3.2.2 Method of Measurement......................................................................... 4-10
20 4.3.2.3 Minimum Standard ................................................................................ 4-10
21 4.3.3 Reverse Pilot Channel to Code Channel Phase Tolerance............................ 4-11
22 4.3.3.1 Definition ............................................................................................... 4-11
23 4.3.3.2 Method of Measurement......................................................................... 4-11
24 4.3.3.3 Minimum Standard ................................................................................ 4-11
25 4.3.4 Waveform Quality and Frequency Accuracy ................................................ 4-11
26 4.3.4.1 Definition ............................................................................................... 4-11
27 4.3.4.2 Method of Measurement......................................................................... 4-11
28 4.3.4.3 Minimum Standard ................................................................................ 4-13
29 4.3.5 Code Domain Power ..................................................................................... 4-13
30 4.3.5.1 Definition ............................................................................................... 4-13
31 4.3.5.2 Method of Measurement......................................................................... 4-13
3GPP2 C.S0011-B
CONTENTS
ix
4.3.5.3 1 Minimum Standard ................................................................................4-14
2 4.4 RF Output Power Requirements ........................................................................4-14
3 4.4.1 Range of Open Loop Output Power ..............................................................4-14
4 4.4.1.1 Definition................................................................................................4-14
5 4.4.1.2 Method of Measurement.........................................................................4-15
6 4.4.1.2.1 Access Channel ..................................................................................4-15
7 4.4.1.2.2 Enhanced Access Channel .................................................................4-17
8 4.4.1.3 Minimum Standard ................................................................................4-20
9 4.4.2 Time Response of Open Loop Power Control ................................................4-23
10 4.4.2.1 Definition................................................................................................4-23
11 4.4.2.2 Method of Measurement.........................................................................4-23
12 4.4.2.3 Minimum Standard ................................................................................4-25
13 4.4.3 Access Probe Output Power .........................................................................4-26
14 4.4.3.1 Definition................................................................................................4-26
15 4.4.3.2 Method of Measurement.........................................................................4-26
16 4.4.3.2.1 Access Channel Probe ........................................................................4-26
17 4.4.3.2.2 Enhanced Access Channel Probe .......................................................4-27
18 4.4.3.3 Minimum Standard ................................................................................4-27
19 4.4.4 Range of Closed Loop Power Control ............................................................4-28
20 4.4.4.1 Definition................................................................................................4-28
21 4.4.4.2 Method of Measurement.........................................................................4-28
22 4.4.4.3 Minimum Standard ................................................................................4-30
23 4.4.5 Maximum RF Output Power.........................................................................4-32
24 4.4.5.1 Definition................................................................................................4-32
25 4.4.5.2 Method of Measurement.........................................................................4-33
26 4.4.5.3 Minimum Standard ................................................................................4-36
27 4.4.6 Minimum Controlled Output Power .............................................................4-38
28 4.4.6.1 Definition................................................................................................4-38
29 4.4.6.2 Method of Measurement.........................................................................4-38
30 4.4.6.3 Minimum Standard ................................................................................4-39
31 4.4.7 Standby Output Power and Gated Output Power ........................................4-39
3GPP2 C.S0011-B
CONTENTS
x
4.4.7.1 1 Definition ............................................................................................... 4-39
2 4.4.7.2 Method of Measurement......................................................................... 4-39
3 4.4.7.3 Minimum Standard ................................................................................ 4-41
4 4.4.8 Power Up Function Output Power ............................................................... 4-42
5 4.4.8.1 Definition ............................................................................................... 4-42
6 4.4.8.2 Method of Measurement......................................................................... 4-42
7 4.4.8.3 Minimum Standard ................................................................................ 4-43
8 4.4.9 Code Channel to Reverse Pilot Channel Output Power Accuracy................ 4-44
9 4.4.9.1 Definition ............................................................................................... 4-44
10 4.4.9.2 Method of Measurement......................................................................... 4-44
11 4.4.9.2.1 Code Channel Output Power for the Enhanced Access Channel
12 Header, Enhanced Access Channel Data, and Reverse Common
13 Control Channel Data ........................................................................ 4-44
14 4.4.9.2.2 Code Channel Output Power for the Reverse Traffic Channel ........... 4-46
15 4.4.9.3 Minimum Standard ................................................................................ 4-48
16 4.4.10 Reverse Pilot Channel Transmit Phase Discontinuity.................................. 4-50
17 4.4.10.1 Definition ............................................................................................... 4-50
18 4.4.10.2 Method of Measurement......................................................................... 4-51
19 4.4.10.3 Minimum Standard ................................................................................ 4-52
20 4.4.11 Reverse Traffic Channel Output Power During Changes in Data Rate ........ 4-52
21 4.4.11.1 Definition ............................................................................................... 4-52
22 4.4.11.2 Method of Measurement......................................................................... 4-53
23 4.4.11.3 Minimum Standard ................................................................................ 4-53
24 4.5 Limitations on Emissions................................................................................... 4-54
25 4.5.1 Conducted Spurious Emissions................................................................... 4-54
26 4.5.1.1 Definition ............................................................................................... 4-54
27 4.5.1.2 Method of Measurement......................................................................... 4-54
28 4.5.1.3 Minimum Standard ................................................................................ 4-56
29 4.5.1.3.1 Spreading Rate 1................................................................................ 4-57
30 4.5.1.3.2 Spreading Rate 3................................................................................ 4-60
31 4.5.2 Radiated Spurious Emissions ...................................................................... 4-61
32 4.5.3 Occupied Bandwidth.................................................................................... 4-61
3GPP2 C.S0011-B
CONTENTS
xi
4.5.3.1 1 Definition................................................................................................4-61
2 4.5.3.2 Method of Measurement.........................................................................4-61
3 4.5.3.3 Minimum Standard ................................................................................4-62
4 5 CDMA ENVIRONMENTAL REQUIREMENTS ..............................................................5-1
5 5.1 Temperature and Power Supply Voltage ..............................................................5-1
6 5.1.1 Definition .......................................................................................................5-1
7 5.1.2 Method of Measurement.................................................................................5-1
8 5.1.3 Minimum Standard ........................................................................................5-2
9 5.2 High Humidity......................................................................................................5-2
10 5.2.1 Definition .......................................................................................................5-2
11 5.2.2 Method of Measurement.................................................................................5-2
12 5.2.3 Minimum Standard ........................................................................................5-3
13 5.3 Vibration Stability ................................................................................................5-3
14 5.3.1 Definition .......................................................................................................5-3
15 5.3.2 Method of Measurement.................................................................................5-3
16 5.3.3 Minimum Standard ........................................................................................5-3
17 5.4 Shock Stability.....................................................................................................5-3
18 5.4.1 Definition .......................................................................................................5-3
19 5.4.2 Method of Measurement.................................................................................5-3
20 5.4.3 Minimum Standard ........................................................................................5-3
21 6 CDMA STANDARD TEST CONDITIONS .....................................................................6-1
22 6.1 Standard Equipment ............................................................................................6-1
23 6.1.1 Basic Equipment ............................................................................................6-1
24 6.1.2 Associated Equipment....................................................................................6-1
25 6.2 Standard Environmental Test Conditions ............................................................6-1
26 6.3 Standard Conditions for the Primary Power Supply.............................................6-1
27 6.3.1 General...........................................................................................................6-1
28 6.3.2 Standard DC Test Voltage from Accumulator Batteries .................................6-1
29 6.3.3 Standard AC Voltage and Frequency..............................................................6-2
30 6.4 Standard Test Equipment ....................................................................................6-2
31 6.4.1 Standard Channel Simulator .........................................................................6-2
3GPP2 C.S0011-B
CONTENTS
xii
6.4.1.1 Channel 1 Model Parameters ...................................................................... 6-2
2 6.4.1.2 Channel Model Parameter Conditions and Tolerances............................. 6-4
3 6.4.1.3 Channel Simulator Configurations........................................................... 6-5
4 6.4.2 Waveform Quality Measurement Equipment ................................................. 6-5
5 6.4.2.1 Rho Meter for Radio Configuration 1 and 2.............................................. 6-5
6 6.4.2.2 Rho Meter for Radio Configuration 3 through 9 ....................................... 6-7
7 6.4.2.2.1 The Ideal Composite Reference Signal ................................................. 6-7
8 6.4.2.2.2 The Transmitter Signal-Under-Test ..................................................... 6-8
9 6.4.2.2.3 Active Code-Channel Identification, Symbol Detection and
10 Parameter Estimation .......................................................................... 6-9
11 6.4.2.2.4 Rho (ρ) ................................................................................................ 6-10
12 6.4.2.2.5 Code-domain Power (CDP) ................................................................. 6-10
13 6.4.2.2.6 Power in Undesired Channels............................................................ 6-12
14 6.4.2.2.7 Code Domain Time Offsets and Phase Offsets Relative to Reverse
15 Pilot Channel ..................................................................................... 6-12
16 6.4.2.3 Code Domain Measurement Equipment Accuracy................................. 6-13
17 6.4.3 Base Station Equipment .............................................................................. 6-13
18 6.4.3.1 Transmitter Equipment .......................................................................... 6-13
19 6.4.3.2 Receiver Equipment ............................................................................... 6-15
20 6.4.3.3 Protocol Support..................................................................................... 6-15
21 6.4.3.4 Timing Signals........................................................................................ 6-15
22 6.4.4 AWGN Generator.......................................................................................... 6-15
23 6.4.5 CW Generator............................................................................................... 6-16
24 6.4.6 Spectrum Analyzer....................................................................................... 6-17
25 6.4.7 Average Power Meter.................................................................................... 6-18
26 6.4.8 Phase Transient Measuring Equipment ....................................................... 6-19
27 6.5 Functional System Set-ups................................................................................ 6-19
28 6.5.1 Functional Block Diagrams.......................................................................... 6-19
29 6.5.2 General Comments ...................................................................................... 6-21
30 6.6 Confidence Limits .............................................................................................. 6-33
31 6.6.1 Confidence Level of Error Rate..................................................................... 6-33
32 6.6.2 Confidence on Power Measurement During Fading..................................... 6-37
3GPP2 C.S0011-B
CONTENTS
xiii
6.6.3 Confidence Level 1 of Detection Time .............................................................6-39
2 ANNEX A: SELECTED PERFORMANCE REQUIREMENTS TABLES ...............................A-1
3 A.1 Forward Common Channel Performance Tables ..................................................A-1
4 A.1.1 Non-Slotted Mode Paging Channel Performance Requirements.....................A-1
5 A.1.1.1 Method of Measurement Test Parameters .............................................A-1
6 A.1.1.2 Minimum Standards Requirements.......................................................A-1
7 A.1.2 Slotted Mode Paging Channel Performance Requirements ............................A-2
8 A.1.2.1 Method of Measurement Test Parameters .............................................A-2
9 A.1.2.2 Minimum Standards Requirements.......................................................A-5
10 A.1.3 Forward Broadcast Control Channel Performance Requirements in
11 AWGN Channel ..............................................................................................A-6
12 A.1.3.1 Method of Measurement Test Parameters .............................................A-7
13 A.1.3.2 Minimum Standards Requirements.......................................................A-9
14 A.1.4 Forward Broadcast Control Channel Performance Requirements in
15 Multipath Fading Channel ...........................................................................A-11
16 A.1.4.1 Method of Measurement Test Parameters ...........................................A-12
17 A.1.4.2 Minimum Standards Requirements.....................................................A-32
18 A.1.5 Forward Common Control Channel Performance Requirements..................A-41
19 A.1.5.1 Method of Measurement Test Parameters ...........................................A-42
20 A.1.5.2 Minimum Standards Requirements.....................................................A-44
21 A.1.6 Common Assignment Channel and Common Power Control Channel
22 Performance Requirements ..........................................................................A-47
23 A.1.6.1 Method of Measurement Test Parameters ...........................................A-48
24 A.1.6.2 Minimum Standards Requirements.....................................................A-49
25 A.2 Forward Traffic Channel Demodulation Performance Tables .............................A-51
26 A.2.1 Forward Traffic Channel Performance Requirements in AWGN ...................A-51
27 A.2.1.1 Method of Measurement Test Parameters ...........................................A-51
28 A.2.1.2 Minimum Standards Requirements.....................................................A-68
29 A.2.2 Forward Traffic Channel Performance Requirements in Multipath Fading
30 Channel........................................................................................................A-90
31 A.2.2.1 Method of Measurement Test Parameters ...........................................A-91
32 A.2.2.2 Minimum Standards Requirements...................................................A-100
3GPP2 C.S0011-B
CONTENTS
xiv
A.2.3 Forward Fundamental Channel Performance 1 Requirements During Soft
2 Handoff.......................................................................................................A-105
3 A.2.3.1 Method of Measurement Test Parameters .........................................A-105
4 A.2.3.2 Minimum Standards Requirements ..................................................A-106
5 A.2.4 Power Control Bit Performance Requirements for Channels Belonging to
6 Different Power Control Sets During Soft Handoff .....................................A-106
7 A.2.4.1 Method of Measurement Test Parameters .........................................A-106
8 A.2.4.2 Minimum Standards Requirements ..................................................A-106
9 A.2.5 Power Control Bit Performance Requirements for Channels Belonging to
10 the Same Power Control Set.......................................................................A-107
11 A.2.5.1 Method of Measurement Test Parameters .........................................A-107
12 A.2.5.2 Minimum Standards Requirements ..................................................A-107
13 A.2.6 Power Control Subchannel Performance Requirements During Soft
14 Handoff.......................................................................................................A-107
15 A.2.6.1 Method of Measurement Test Parameters .........................................A-108
16 A.2.6.2 Minimum Standards Requirements ..................................................A-108
17 A.2.7 Forward Traffic Channel Performance Requirements in Multipath Fading
18 Channel with Closed Loop Power Control (FPC_MODE = ‘000’) .................A-108
19 A.2.7.1 Method of Measurement Test Parameters .........................................A-108
20 A.2.7.2 Minimum Standards Requirements ..................................................A-114
21 A.2.8 Forward Traffic Channel Performance Requirements in Multipath Fading
22 Channel with Closed Loop Power Control (FPC_MODE = ‘010’) .................A-119
23 A.2.8.1 Method of Measurement Test Parameters .........................................A-119
24 A.2.8.2 Minimum Standards Requirements ..................................................A-127
25 A.2.9 Forward Traffic Channel Performance Requirements in Multipath Fading
26 Channel with Outer Loop Power Control and Closed Loop Power Control
27 (FPC_MODE = ‘000’, ‘001’ and ‘010’) ..........................................................A-134
28 A.2.9.1 Method of Measurement Test Parameters .........................................A-135
29 A.2.9.2 Minimum Standards Requirements ..................................................A-138
30 A.2.10 Forward Traffic Channel Performance Requirements in Multipath Fading
31 with Closed Loop Power Control (FPC_MODE = ‘000’) and Transmit
32 Diversity (OTD or STS) ...............................................................................A-140
33 A.2.10.1 Method of Measurement Test Parameters .........................................A-140
34 A.2.10.2 Minimum Standards Requirements ..................................................A-144
3GPP2 C.S0011-B
CONTENTS
xv
A.2.11 Forward Traffic Channel Performance Requirements 1 in Multipath Fading
2 with Closed Loop Power Control (FPC_MODE = ‘010’) and Transmit
3 Diversity (OTD or STS) ...............................................................................A-149
4 A.2.11.1 Method of Measurement Test Parameters .........................................A-149
5 A.2.11.2 Minimum Standards Requirements...................................................A-153
6 A.2.12 Power Control Subchannel Performance Requirements During Reverse
7 Pilot Channel Gating ..................................................................................A-154
8 A.2.12.1 Method of Measurement Test Parameters .........................................A-155
9 A.2.12.2 Minimum Standards Requirements...................................................A-155
10 A.2.13 Power Control Subchannel Performance Requirements During Reverse
11 Fundamental Channel Gating....................................................................A-155
12 A.2.13.1 Method of Measurement Test Parameters .........................................A-155
13 A.2.13.2 Minimum Standards Requirements...................................................A-156
【文件名】:071126@52RD_3GPP2 C.S0011-B IS-98E(1).pdf
【格　式】:pdf
【大　小】:1844K
【简　介】:
【目　录】: