发个测试配置文件，包忙结解释下

527263610

#################################################################################################
#                                                                                               #
# CFT calibration parameter configuration file                                     CALPARAM.INI #
# Copyright (c) 2007-2009 Spreadtrum Corporation                                    2010/06/30  #
#                                                                                               #
#################################################################################################

;=================================================================================================
;内容[Content]
;=================================================================================================
;This file define all the parameters and spec. used in calibraiton process:
;这个文件定义了所有校准过程中的的参数配置。
;including: ADC, AFC, APC, AGC.
;包括了：ADC，AFC，APC，AGC

;=================================================================================================
;修订历史[Modify History]
;=================================================================================================


[Project]
;
Automatic Detect Chip =0
;
BaseBand Chip =1
;
;SPSC_UNKNOWN = -1, //
;SPSC_6600D   =  0, // SC6600D
;SPSC_6600M   =  1, // SC6600M
;SPSC_6800    =  2, // SC6800
;SPSC_8800    =  4, // SC8800D/SC8800H/SC8800S     
;
ADC_DLL=ADC.dll
;
AFC_DLL=QuorumCrystal.dll
;DCXO.dll
;TCXO.dll
;QuorumCrystal.dll
;
;
AGC_DLL=QuorumAgc.dll
;QuorumAgc.dll
;
;
;
;
APC_DLL=AxiomApc.dll
;SkyworksApc.dll
;RfmdApc.dll
;AxiomApc.dll
;
;



;*************************************************************************************************
;
;                                         电池校准[ADC]
;
;*************************************************************************************************

# BATTERY
-------------
[ADC-BATTARY]
Item Number           =2
Use DC Output Voltage =1
Change Voltage Sleep  = 200  ; ms

[ADC-BATTARY Item 0]
Command ID            =6
Voltage               =4200
Average Count         =3
ADC Low  Limit              =724
ADC High Limit              =1086

[ADC-BATTARY Item 1]
Command ID            =6
Voltage               =3600               
Average Count         =3
ADC Low  Limit              =0
ADC High Limit              =1000

# Battery Verification
----------------------
[ADC-BATTERY VERIFY]
Command ID            =6
Voltage               =3800
Voltage Delta Range   =40



[ADAPT ADC CALIBRATION]

; Disable adapt calibration, using old calibration
; [强制关闭自适应电池校准，采用旧方式校准]
Force Disable Adapt Calibration = 0

; Calibration ouput voltage(Unit: mV)
; [校准输出电压：4.2V 和 3.6V]
Calibration Voltages = 4200, 3600

; Sleep time (ms) after changing output voltage
; [输出电压改变之后等待时间，确保电压稳定输出]
Sleep Time after Change Voltage = 200  ; ms

; Calibration average times for each voltage
; [每个输出电压的平均校准次数]
Average Count = 3

; ADC low/high limit specification for voltage1 and voltage2
; [校准输出电压1和校准输出电压2对应的ADC0-ADC7范围检查]
;                        | adc0 | adc1 | adc2 | adc3 | adc4 | adc5 | adc6 | adc7 |
;--------------------------------------------------------------------------------------
Voltage1 ADC Low  Limit =  724,   724,   724,   724,   724,   724,   724,   724
Voltage1 ADC High Limit =  1086,  1086,  1086,  1086,  1086,  1086,  1086,  1086
Voltage2 ADC Low  Limit =  0,     0,     0,     0,     0,     0,     0,     0
Voltage2 ADC High Limit =  1000,  1000,  1000,  1000,  1000,  1000,  1000,  1000

; Verify calibration result
; [验证校准结果]
;                        | adc0 | adc1 | adc2 | adc3 | adc4 | adc5 | adc6 | adc7 |
;--------------------------------------------------------------------------------------
Check Output Voltage     = 3800,  3800,  3800,  3800,  3800,  3800,  3800,  3800
Check Delta Voltage Range= 40,    40,    40,    40,    40,    40,    40,    40

;*************************************************************************************************
;
;                                       自动频率校准[AFC]
;
;*************************************************************************************************

[AFC-COMMON]
;
BAND              =0
;EGSM900=0,
;DCS1800=1,
;EGSM_DCS_DUALBAND=2,
;PCS1900          =3,
;GSM850           =4,
;EGSM_PCS_DUALBAND=5,
;GSM850_DCS_DUALBAND=6,
;GSM850_PCS_DUALBAND=7,
;GSM850_EGSM_DUALBAND=8,
;GSM850_EGSM_PCS_TRIBAND=9,
;GSM850_EGSM_DCS_TRIBAND=10,
;TD=11,
;
FACTOR            =10000

PCL               =10      
TCH               =62      


# CRYSTAL
-------------
[CRYSTAL_QS518]
Default CDAC      =55
CDAC    Range     =15

Default CAFC      =7000
Delta   CAFC      =1000
CAFC    Range     =1000

Slope Range       =3

;*************************************************************************************************
;
;                                    自动功率校准[APC]
;
;*************************************************************************************************

# 期望功率SPEC.
----------------------
[GSM850M TX TARGET POWER]
# PCL         5     6     7     8     9    10    11    12    13    14    15    16    17    18    19    19  
------------------------------------------------------------------------------------------------------------
PCL       =32.00, 30.70, 29.10, 26.90, 25.00, 23.00, 21.00, 19.00, 17.00, 15.00, 13.00, 11.00, 9.00, 7.00, 5.00, 5.00
TOLERANCE =0.40,  0.40,  0.60,  0.60,  0.60,  0.60,  0.60,  0.60,  0.60,  0.60,  0.60,  0.80,  1.00, 1.20, 1.50, 1.50

[EGSM900 TX TARGET POWER]
# PCL         5     6     7     8     9    10    11    12    13    14    15    16    17    18    19    19  
------------------------------------------------------------------------------------------------------------
PCL       =32.00, 30.80, 29.00, 27.00, 25.00, 23.00, 21.00, 19.00, 17.00, 15.00, 13.00, 11.00, 9.00, 7.00, 5.00, 5.00
TOLERANCE =0.30,  0.40,  0.60,  0.60,  0.60,  0.60,  0.60,  0.60,  0.60,  0.60,  0.60,  0.80,  1.00, 1.20, 1.50, 1.50

[DCS1800 TX TARGET POWER]
# PCL         0     1     2     3     4     5     6     7     8     9    10    11    12    13    14    15
------------------------------------------------------------------------------------------------------------  
PCL       =29.20, 27.50, 26.00, 24.00, 22.00, 20.00, 18.00, 16.00, 14.00, 12.00, 10.00, 8.00, 6.00, 4.00, 2.00, 2.00
TOLERANCE =0.30,  0.40,  0.60,  0.60,  0.60,  0.60,  0.60,  0.60,  0.60,  0.60,  0.60,  0.80, 1.00, 1.20, 1.50, 1.50

[PCS1900 TX TARGET POWER]
# PCL         0     1     2     3     4     5     6     7     8     9    10    11    12    13    14    15
------------------------------------------------------------------------------------------------------------  
PCL       =29.20, 27.50, 26.00, 24.00, 22.00, 20.00, 18.00, 16.00, 14.00, 12.00, 10.00, 8.00, 6.00, 4.00, 2.00, 2.00
TOLERANCE =0.40,  0.40,  0.60,  0.60,  0.60,  0.60,  0.60,  0.60,  0.60,  0.60,  0.60,  0.80, 1.00, 1.20, 1.50, 1.50


[EGSM900 FULL PCL APC]
; Full PCL Calibration [全部功率等级校准]
SWEEP STEP              = 0.2, 0.3, 0.5

CAL FULL PCL            = 1
CAL FULL DEFAULT FACTOR = 28799,27855,26693,25517,23693,21266,19094,17266,15888,14799,13942,13260,12263,10532,8859,8859

; Part PCL Calibration [部分功率等级校准]
; Only available when CAL FULL PCL = 0
CAL LIST LINE LOWER PCL = 5,  9, 13, 17
CAL LIST CAL PCL        = 6, 11, 15, 18
CAL LIST DEFAULT FACTOR = 27394, 18988, 13669, 10000
CAL LIST LINE UPPER PCL = 8, 12, 16, 19

; Simulate Line factor step
SIMULATE LOWER POWER    = 0,    10,  17,   26
SIMULATE SLOPE VALUE    = 820, 430, 1150, 810
SIMULATE UPPER POWER    = 10,   17,  26,   34

#-------
Channel Compensate Lower   =1
Channel Compensate Low     =1
Channel Compensate High    =0
Channel Compensate Higher  =0

#
Log Data To File        = 1

[DCS1800 FULL PCL APC]
SWEEP STEP              = 0.2, 0.3, 0.5

CAL FULL PCL            = 1
CAL FULL DEFAULT FACTOR = 28323,27128,26062,24782,22564,20055,17862,15995,14533,12857,10973,8889,7026,5631,4737,4737


CAL LIST LINE LOWER PCL = 0,  4,  8, 13
CAL LIST CAL PCL        = 1,  5, 10, 14
CAL LIST DEFAULT FACTOR = 26820, 22152, 11746, 4734
CAL LIST LINE UPPER PCL = 3,  7, 12, 15

SIMULATE LOWER POWER    = -5,    5,    16,   23.5
SIMULATE SLOPE VALUE    = 470,  860,  1250,  700
SIMULATE UPPER POWER    = 5,    16,   23.5,  33

#-------
Channel Compensate Lower   =1
Channel Compensate Low     =0
Channel Compensate High    =0
Channel Compensate Higher  =1

Log Data To File        = 1


[PCS1900 FULL PCL APC]
SWEEP STEP              = 0.2, 0.3, 0.5

CAL FULL PCL            = 1
CAL FULL DEFAULT FACTOR = 31200,28900,27300,25800,24500,22700,20200,17600,15500,13800,12300,10600,8700,6700,5700,5000


CAL LIST LINE LOWER PCL = 0,  4,  8, 13
CAL LIST CAL PCL        = 1,  5, 10, 14
CAL LIST DEFAULT FACTOR = 26820, 22152, 11746, 4734
CAL LIST LINE UPPER PCL = 3,  7, 12, 15

SIMULATE LOWER POWER    = -5,    5,    16,   23.5
SIMULATE SLOPE VALUE    = 470,  860,  1250,  700
SIMULATE UPPER POWER    = 5,    16,   23.5,  33

#-------
Channel Compensate Lower   =1
Channel Compensate Low     =0
Channel Compensate High    =0
Channel Compensate Higher  =1

Log Data To File        = 1



[GSM850M FULL PCL APC]
; Full PCL Calibration [全部功率等级校准]
SWEEP STEP              = 0.2, 0.3, 0.5

CAL FULL PCL            = 1
CAL FULL DEFAULT FACTOR = 28200,27100,25800,24200,23300,20800,18500,16400,15100,14200,13300,12600,11600,9600,7900

; Part PCL Calibration [部分功率等级校准]
; Only available when CAL FULL PCL = 0
CAL LIST LINE LOWER PCL = 5,  9, 13, 17
CAL LIST CAL PCL        = 6, 11, 15, 18
CAL LIST DEFAULT FACTOR = 27394, 18988, 13669, 10000
CAL LIST LINE UPPER PCL = 8, 12, 16, 19

; Simulate Line factor step
SIMULATE LOWER POWER    = 0,    10,  17,   26
SIMULATE SLOPE VALUE    = 820, 430, 1150, 810
SIMULATE UPPER POWER    = 10,   17,  26,   34

#-------
Channel Compensate Lower   =1
Channel Compensate Low     =0
Channel Compensate High    =0
Channel Compensate Higher  =1

Log Data To File        = 1

;*************************************************************************************************
;
;                                    自动增益校准[AGC]
;
;*************************************************************************************************

[AGC COMMON SETTING]

# 信道补偿设置 channel compensate
---
;                       |   GSM850M    |   EGSM    |    DCS   |    PCS    |
;-------------------------------------------------------------------------------------------
Compensate Arfcn Gap   =40, 40, 80, 80
Max. Compensate Value  =128, 128, 128, 128

# 增益校准参数
[QUORUM QS518 AGC]
Calibration Cell Power =-90.00, -70.00, -50.00, -30.00
Calibration Gain Value =0xFD5, 0xB4D, 0x911, 0x112
; Unit: dB
Max. Delta RSSI Range  =10, 10, 10, 10
Calibration Target RSSI=0xFEA0
Min. Gain Value        =105
Mid2 Gain Value        =2344
Mid1 Gain Value        =2920
Max. Gain Value        =4072
Max. Gain Max. Count   =10

# 信道补偿参数 channel compensate
---
;                       |  GSM850M    |   EGSM    |    DCS   |    PCS    |
;-------------------------------------------------------------------------------------------
Compensate Cell Power  =-70.00, -70.00, -70.00, -70.00
Compensate Target RSSI =0xFEA0, 0xFEA0, 0xFEA0, 0xFEA0   

;*************************************************************************************************
;
;                                      Longcheer BT Test
;
;*************************************************************************************************


;BT参数
[BT Parameter]
;是否双电源校准
DUAL BATTERY=0;

;做BT/FT的频段
[FT Band Number]
GSM900=1;
DCS1800=1;
PCS1900=0;
GSM850=0;

























;*************************************************************************************************
;
;                                     MISC. SETTING
;
;*************************************************************************************************
[Final Test]
;并发测试延时设置
First Concurrent Test Wait = 800   ; ms
RX Concurrent Test Wait    = 100   ; ms

; FT 重测设置
ReFT Total Count           = 0
ReFT Interval Sleep        = 200   ; ms

[Test Time]
; ms Default: 180 seconds
Total TestTime Limit       = 180000


;*************************************************************************************************
;
;                                      CURRENT TEST
;
;*************************************************************************************************
[Current Test]
Test Items = Deep Sleep,Vibrate On,Led On

[Deep Sleep]
Test State  =1
Wait Time   =3000
Lower Limit =0.01
Upper Limit =2.00

[Vibrate On]
Test State  =0
Wait Time   =300
Lower Limit =0.01
Upper Limit =100.00

[Led On]
Test State  =0
Wait Time   =300
Lower Limit =0.01
Upper Limit =100.00
[APC_TD_QS3200_DualBand]
Arfcn_Num=3
[AGC_TD_QS3200_DualBand]
Arfcn_Num=3


[GSM900Test]   
;Spec
ExpectedPowerMax =34.5,33,31,29,27,25,23,21,19,18,16,14,12,10,8,8
ExpectedPower    =33.0,31,29,27,25,23,21,19,17,15,13,11,9, 7, 5
ExpectedPowerMin =31.5,29,27,25,23,21,19,17,15,12,10,8,6,4,2,2
FrequencyTolerance=-90.00,90.00
PhaseRMSTolerance=0,5
PhasePeakTolerance=0,20
RxlevelTolerance=2,3,4
RxQualityTolerance=0,4
BerErrorTolerance=0,2
;
;Test Items
Arfcn= 64
PCL= 5
Power=1
PowerVsTime=1
Frequency=1
Orfs=1
CellPower=-102
Rxlevel=1
BER =1
RxQuality=0
;

[DCS1800Test]  
;Spec
ExpectedPowerMax =31.5,30,28,26,24,22,20,18,16,15,13,11,9,7,5,5
ExpectedPower    =30,28,26,24,22,20,18,16,14,12,10,8,6,4,2,0
ExpectedPowerMin =28.5,26,24,22,20,18,16,14,12,9,7,5,3,1,-1,-5
FrequencyTolerance=-180.0,180.0
PhaseRMSTolerance=0,5
PhasePeakTolerance=0,20
RxlevelTolerance=2,4,4
RxQualityTolerance=0,4
BerErrorTolerance=0,2
;
;Test Items
Arfcn= 700
PCL= 0
Power=1
PowerVsTime=1
Frequency=1
Orfs=1
CellPower=-102
Rxlevel=1
BER =1
RxQuality=0
;

[PCS1900Test]  
;Spec
ExpectedPowerMax =31.5,30,28,26,24,22,20,18,16,15,13,11,9,7,5,5
ExpectedPower    =30,28,26,24,22,20,18,16,14,12,10,8,6,4,2,0
ExpectedPowerMin =28.5,26,24,22,20,18,16,14,12,9,7,5,3,1,-1,-5
FrequencyTolerance=-180.0,180.0
PhaseRMSTolerance=0,5
PhasePeakTolerance=0,20
RxlevelTolerance=2,4,4
RxQualityTolerance=0,4
BerErrorTolerance=0,2
;
;Test Items
Arfcn= 661
PCL= 0
Power=1
PowerVsTime=1
Frequency=1
Orfs=1
CellPower=-102
Rxlevel=1
BER =1
RxQuality=0
;

[GSM850Test]   
;Spec
ExpectedPowerMax =34.5,33,31,29,27,25,23,21,19,18,16,14,12,10,8,8
ExpectedPower    =33.0,31,29,27,25,23,21,19,17,15,13,11,9, 7, 5
ExpectedPowerMin =31.5,29,27,25,23,21,19,17,15,12,10,8,6,4,2,2
FrequencyTolerance=-90.00,90.00
PhaseRMSTolerance=0,5
PhasePeakTolerance=0,20
RxlevelTolerance=2,3,4
RxQualityTolerance=0,4
BerErrorTolerance=0,2
;
;Test Items
Arfcn= 190
PCL= 5
Power=1
PowerVsTime=1
Frequency=1
Orfs=1
CellPower=-102
Rxlevel=1
BER =1
RxQuality=0
;

【文件名】:SX3100BCAL_20110422(900,1800).rar
【格　式】:rar
【大　小】:3K
【简　介】:
【目　录】: