谁能告诉我,下面的中文含义是什么???能否具体点,谢谢!

shizhijie

Location update Fail = 101
MT Call Fail = 102
Call Drop = 103
Average Burst Power Fail = 104
Peak Burst Power Fail = 105
PVT Match Fail = 106
Timing Error Fail = 107
Phase Error Peak Fail = 108
Phase Error RMS Fail = 109
Frequency Error Fail = 110
Spectrum due to Modulation Fail = 111
Spectrum due to Switching Fail = 112
Rx Quality Fail = 113
Rx Level Fail = 114
BER Fail = 115
BLER Fail = 116
METAAPP_GET_AVAILABLE_HANDLE_FAIL = 201
METAAPP_OPEN_UART_FAIL = 202
METAAPP_CLOSE_UART_FAIL = 203
METAAPP_BOOT_FAIL = 204
METAAPP_BOOT_STOP_FAIL = 205
METAAPP_INIT_FAIL = 206
METAAPP_WAIT_FOR_TARGET_READY_FAIL = 207
METAAPP_COMM_SET_BAUD_RATE_FAIL = 208
METAAPP_COMM_START_FAIL = 209
METAAPP_COMM_STOP_FAIL = 210
METAAPP_CONNECT_WITH_TARGET_FAIL = 211
METAAPP_DISCONNECT_WITH_TARGET_FAIL = 212
METAAPP_RF_SELECT_BAND_FAIL = 213
METAAPP_RF_SELECT_BAND_CNF_FAIL = 214
METAAPP_RF_AFC_MEASURE_FAIL = 215
METAAPP_RF_AFC_MEASURE_CNF_FAIL = 216
METAAPP_RF_AFC_SET_DAC_VALUE_FAIL = 217
METAAPP_RF_AFC_SET_DAC_VALUE_CNF_FAIL = 218
METAAPP_RF_CRYSTALAFC_SET_CAPID_FAIL = 219
METAAPP_RF_PM_FAIL = 220
METAAPP_RF_NB_TX_FAIL = 221
METAAPP_RF_NB_TX_CNF_FAIL = 222
METAAPP_RF_SET_APC_LEVEL_DAC_FAIL = 223
METAAPP_RF_SET_APC_LEVEL_DAC_CNF_FAIL = 224
METAAPP_RF_STOP_FAIL = 225
METAAPP_RF_STOP_CNF_FAIL = 226
METAAPP_RF_BBTXAUTOCAL_FAIL = 227
METAAPP_RF_GETBBTXCFG2_FAIL = 228
METAAPP_RF_SETBBTXCFG2_FAIL = 229
METAAPP_RF_SETAFCSINEWAVEDETECT_FAIL = 230
METAAPP_RF_SET_MT6140CW2_TO_REG_FAIL = 231
METAAPP_RF_GET_MT6140ACODE_FROM_REG_FAIL = 232
METAAPP_RF_GET_RFID_FAIL = 233
METAAPP_NVRAM_INIT_FAIL = 234
METAAPP_NVRAM_AFC_SLOPE_INVALID_FAIL = 235
METAAPP_NVRAM_AGC_PATHLOSS_LEN_FAIL = 236
METAAPP_NVRAM_GET_REC_LEN_FAIL = 237
METAAPP_NVRAM_GET_RAMPTABLE_LEN_FAIL = 238
METAAPP_NVRAM_COMPOSE_AGC_PATHLOSS_FAIL = 239
METAAPP_NVRAM_DECOMPOSE_AGC_PATHLOSS_FAIL = 240
METAAPP_NVRAM_COMPOSE_RAMPTABLE_FAIL = 241
METAAPP_NVRAM_DECOMPOSE_RAMPTABLE_FAIL = 242
METAAPP_NVRAM_SET_REC_FIELD_VALUE_FAIL = 243
METAAPP_NVRAM_GET_REC_FIELD_VALUE_FAIL = 244
METAAPP_NVRAM_COMPOSE_ADC_CAL_TABLE_FAIL = 245
METAAPP_NVRAM_DECOMPOSE_ADC_CAL_TABLE_FAIL = 246
METAAPP_NVRAM_COMPOSE_BARCODE_FAIL = 247
METAAPP_NVRAM_DECOMPOSE_BARCODE_FAIL = 248
METAAPP_NVRAM_COMPOSE_IMEI_FAIL = 249
METAAPP_NVRAM_DECOMPOSE_IMEI_FAIL = 250
METAAPP_NVRAM_COMPOSE_IP2_FAIL = 251
METAAPP_NVRAM_DECOMPOSE_IP2_FAIL = 252
METAAPP_NVRAM_WRITE_FAIL = 253
METAAPP_NVRAM_WRITE_CNF_FAIL = 254
METAAPP_NVRAM_READ_FAIL = 255
METAAPP_NVRAM_READ_CNF_FAIL = 256
METAAPP_NVRAM_COMPOSE_SECURITY_FAIL = 257
METAAPP_NVRAM_DECOMPOSE_SECURITY_FAIL = 258
METAAPP_NVRAM_GET_TXIQ_LEN_FAIL = 259
METAAPP_NVRAM_COMPOSE_TXIQ_FAIL = 260
METAAPP_NVRAM_DECOMPOSE_TXIQ_FAIL = 261
METAAPP_NVRAM_COMPOSE_SETTINGBAND_FAIL = 262
METAAPP_NVRAM_DECOMPOSE_SETTINGBAND_FAIL = 263
METAAPP_NVRAM_COMPOSE_CUST_ACOUSTIC_FAIL = 264
METAAPP_NVRAM_DECOMPOSE_CUST_ACOUSTIC_FAIL = 265
METAAPP_FILE_READ_FAIL = 266
METAAPP_FILE_WRITE_FAIL = 267
METAAPP_IMEI_CALCULATE_CD_FAIL = 268
METAAPP_ADC_READ_FROM_NVRAM_CNF_FAIL = 269
METAAPP_ADC_MEASURE_FAIL = 270
METAAPP_ADC_MEASURE_CNF_FAIL = 271
METAAPP_GET_VERSION_INFO_FAIL = 272
METAAPP_GET_VERSION_INFO_CNF_FAIL = 273
METAAPP_FAT_OPEN_FAI = 274
METAAPP_FAT_CLOSE_FAIL = 275
METAAPP_FAT_GET_FILE_SIZE_FAIL = 276
METAAPP_FAT_READ_TO_FILE_FAIL = 277
METAAPP_FAT_WRITE_BY_FILE_FAIL = 278
METAAPP_FAT_DELETE_FAIL = 279
METAAPP_FAT_FIND_START_FAIL = 280
METAAPP_FAT_FIND_HEAD_FAIL = 281
METAAPP_FAT_FIND_PREV_FAIL = 282
METAAPP_FAT_FIND_NEXT_FAIL = 283
METAAPP_FAT_FIND_GET_DISK_INFO_FAIL = 284
METAAPP_FAT_GET_DISK_INFO_FAIL = 285
METAAPP_QUERY_TWO_APC_DC_OFFSET_SUPPORT_FAIL = 286
METAAPP_TIMEOUT_FAIL = 287
BARCODE_LIMIT_FAIL = 288
AFC Calibration Fail = 301
Pathloss Calibration Fail = 302
APC Calibration Fail = 303
PHASE ERROR Calibration Fail = 304
ADC Calibration Fail = 305
IP2 Calibration Fail = 306

jiangxu520

Error Code]
Lacation update Fail = 101;位置更新错误
MT Call Fail = 102;手机呼叫失败
Call Drop = 103;掉线
Average Burst Power Fail = 104;平均突发功率超出模板
Peak Burst Power Fail = 105;峰值突发功率超出模板
PVT Match Fail = 106; PVT超出模板
Timing Error Fail = 107;时序偏差超出模板
Phase Error Peak Fail = 108;峰值相位误差超出模板
Phase Error RMS Fail = 109;均值相位误差超出模板
Frequency Error Fail = 110;频率误差超出范围
Spectrum due to Modulation Fail = 111;调制频谱超出模板
Spectrum due to Switching Fail = 112;开关频谱超出模板
Rx Quality Fail = 113;接收灵敏度超出范围
Rx Level Fail = 114;接收电平超出范围
BER Fail = 115;误码率超出范围
BLER Fail = 116;误块率超出范围
METAAPP_GET_AVAILABLE_HANDLE_FAIL = 201;Meta可用到的操作失败
METAAPP_OPEN_UART_FAIL = 202;Meta打开Uart口失败
METAAPP_CLOSE_UART_FAIL = 203;Meta关闭Uart口失败
METAAPP_BOOT_FAIL = 204;Meta连通串口失败
METAAPP_BOOT_STOP_FAIL = 205;Meta终止连通串口失败
METAAPP_INIT_FAIL = 206;Meta初始化失败
METAAPP_WAIT_FOR_TARGET_READY_FAIL = 207;Meta等待被测件准备失败
METAAPP_COMM_SET_BAUD_RATE_FAIL = 208;Meta命令设置波特率失败
METAAPP_COMM_START_FAIL = 209；Meta命令开始失败
METAAPP_COMM_STOP_FAIL = 210；Meta命令终止失败
METAAPP_CONNECT_WITH_TARGET_FAIL = 211；Meta连接被测件失败
METAAPP_DISCONNECT_WITH_TARGET_FAIL = 212；Meta断开被测件失败
METAAPP_RF_SELECT_BAND_FAIL = 213；Meta选择射频频段失败
METAAPP_RF_SELECT_BAND_CNF_FAIL = 214
METAAPP_RF_AFC_MEASURE_FAIL = 215；Meta测量AFC失败
METAAPP_RF_AFC_MEASURE_CNF_FAIL = 216;Meta测量AFC配置失败
METAAPP_RF_AFC_SET_DAC_VALUE_FAIL = 217;Meta设置数模转换电压失败
METAAPP_RF_AFC_SET_DAC_VALUE_CNF_FAIL = 218；Meta设置数模转换电压配置失败
METAAPP_RF_CRYSTALAFC_SET_CAPID_FAIL = 219；Meta控制晶体设置CAPID失败
METAAPP_RF_PM_FAIL = 220；Meta控制电源管理失败
METAAPP_RF_NB_TX_FAIL = 221；Meta控制邻道发射失败
METAAPP_RF_NB_TX_CNF_FAIL = 222；Meta控制邻道发射配置失败
METAAPP_RF_SET_APC_LEVEL_DAC_FAIL = 223；Meta设置APC等级数模转换控制失败
METAAPP_RF_SET_APC_LEVEL_DAC_CNF_FAIL = 224；Meta设置APC等级数模转换配置失败
METAAPP_RF_STOP_FAIL = 225；Meta终止失败
METAAPP_RF_STOP_CNF_FAIL = 226；Meta终止配置失败
METAAPP_RF_BBTXAUTOCAL_FAIL = 227；Meta控制基带发射自动校准失败
METAAPP_RF_GETBBTXCFG2_FAIL = 228
METAAPP_RF_SETBBTXCFG2_FAIL = 229
METAAPP_RF_SETAFCSINEWAVEDETECT_FAIL = 230
METAAPP_RF_SET_MT6140CW2_TO_REG_FAIL = 231
METAAPP_RF_GET_MT6140ACODE_FROM_REG_FAIL = 232
METAAPP_RF_GET_RFID_FAIL = 233
METAAPP_RF_GET_IMMEIDATE_BSI_FAIL = 234
METAAPP_RF_SET_IMMEIDATE_BSI_FAIL = 235
METAAPP_RF_MULTISLOT_TX_FAIL = 236；Meta控制多时隙发射失败
METAAPP_RF_EPSK_SET_APC_LEVEL_DAC_FAIL = 237
METAAPP_NVRAM_INIT_FAIL = 238；Meta控制NVRAM初始化失败
METAAPP_NVRAM_AFC_SLOPE_INVALID_FAIL = 239
METAAPP_NVRAM_AGC_PATHLOSS_LEN_FAIL = 240
METAAPP_NVRAM_GET_REC_LEN_FAIL = 241
METAAPP_NVRAM_GET_RAMPTABLE_LEN_FAIL = 242
METAAPP_NVRAM_COMPOSE_AGC_PATHLOSS_FAIL = 243
METAAPP_NVRAM_DECOMPOSE_AGC_PATHLOSS_FAIL = 244
METAAPP_NVRAM_COMPOSE_RAMPTABLE_FAIL = 245
METAAPP_NVRAM_DECOMPOSE_RAMPTABLE_FAIL = 246
METAAPP_NVRAM_SET_REC_FIELD_VALUE_FAIL = 247
METAAPP_NVRAM_GET_REC_FIELD_VALUE_FAIL = 248
METAAPP_NVRAM_COMPOSE_ADC_CAL_TABLE_FAIL = 249
METAAPP_NVRAM_DECOMPOSE_ADC_CAL_TABLE_FAIL = 250
METAAPP_NVRAM_COMPOSE_BARCODE_FAIL = 251
METAAPP_NVRAM_DECOMPOSE_BARCODE_FAIL = 252
METAAPP_NVRAM_COMPOSE_IMEI_FAIL = 253
METAAPP_NVRAM_DECOMPOSE_IMEI_FAIL = 254
METAAPP_NVRAM_COMPOSE_IP2_FAIL = 255
METAAPP_NVRAM_DECOMPOSE_IP2_FAIL = 256
METAAPP_NVRAM_WRITE_FAIL = 257
METAAPP_NVRAM_WRITE_CNF_FAIL = 258
METAAPP_NVRAM_READ_FAIL = 259
METAAPP_NVRAM_READ_CNF_FAIL = 260
METAAPP_NVRAM_COMPOSE_SECURITY_FAIL = 261
METAAPP_NVRAM_DECOMPOSE_SECURITY_FAIL = 262
METAAPP_NVRAM_GET_TXIQ_LEN_FAIL = 263
METAAPP_NVRAM_COMPOSE_TXIQ_FAIL = 264
METAAPP_NVRAM_DECOMPOSE_TXIQ_FAIL = 265
METAAPP_NVRAM_COMPOSE_SETTINGBAND_FAIL = 266
METAAPP_NVRAM_DECOMPOSE_SETTINGBAND_FAIL = 267
METAAPP_NVRAM_COMPOSE_CUST_ACOUSTIC_FAIL = 268
METAAPP_NVRAM_DECOMPOSE_CUST_ACOUSTIC_FAIL = 269
METAAPP_NVRAM_LOCK_FAIL = 270
METAAPP_FILE_READ_FAIL = 271
METAAPP_FILE_WRITE_FAIL = 272
METAAPP_IMEI_CALCULATE_CD_FAIL = 273
METAAPP_ADC_READ_FROM_NVRAM_CNF_FAIL = 274
METAAPP_ADC_MEASURE_FAIL = 275
METAAPP_ADC_MEASURE_CNF_FAIL = 276
METAAPP_GET_VERSION_INFO_FAIL = 277
METAAPP_GET_VERSION_INFO_CNF_FAIL = 278
METAAPP_FAT_OPEN_FAIL = 279
METAAPP_FAT_CLOSE_FAIL = 280
METAAPP_FAT_GET_FILE_SIZE_FAIL = 281
METAAPP_FAT_READ_TO_FILE_FAIL = 282
METAAPP_FAT_WRITE_BY_FILE_FAIL = 283
METAAPP_FAT_DELETE_FAIL = 284
METAAPP_FAT_FIND_START_FAIL = 285
METAAPP_FAT_FIND_HEAD_FAIL = 286
METAAPP_FAT_FIND_PREV_FAIL = 287
METAAPP_FAT_FIND_NEXT_FAIL = 288
METAAPP_FAT_FIND_GET_DISK_INFO_FAIL = 289
METAAPP_FAT_GET_DISK_INFO_FAIL = 290
METAAPP_QUERY_TWO_APC_DC_OFFSET_SUPPORT_FAIL = 291
METAAPP_BT_ADDRESS_FORMAT_FAIL = 292；Meta控制蓝牙地址格式化失败
METAAPP_WIFI_SET_REGDOMAIN_FAIL = 293；Meta控制WIFI设置注册表失败
METAAPP_WIFI_SET_TXPOWER_FAIL = 294；Meta控制WIFI设置发射功率失败
METAAPP_WIFI_CONTTX_FAIL = 295；Meta控制WIFI连续发射失败
METAAPP_WIFI_CSM_FAIL = 296
METAAPP_WIFI_CONTPKTTX_FAIL = 297
METAAPP_WIFI_QUERY_TX_STATUS_FAIL = 298；Meta查询发射状态失败
METAAPP_WIFI_CONTPKTRX_FAIL = 299；
METAAPP_WIFI_QUERY_RX_STATUS_FAIL = 300;Meta查询接收状态失败
METAAPP_WIFI_QUERY_RX_COUNTER_FAIL = 301；Meta查询WIFI接收计数器失败
METAAPP_WIFI_QUERY_CHIPCAP_FAIL = 302；Meta查询WIFI芯片上面容值失败
METAAPP_WIFI_QUERY_CHANNELLIST_FAIL = 303；Meta查询WIFI通道清单失败
METAAPP_WIFI_STOP_FAIL = 304;Meta停止Wifi失败
METAAPP_TIMEOUT_FAIL = 305;Meta延时失败
BARCODE_LIMIT_FAIL = 306；条形码极限超出范围
AFC Calibration Fail = 501;AFC校准失败
Pathloss Calibration Fail = 502;接收路径校准超出范围
APC Calibration Fail = 503;APC校准失败
PHASE ERROR Calibration Fail = 504;相位误差超出范围
ADC Calibration Fail = 505;ADC校准失败
IP2 Calibration Fail = 506;二阶交调超出范围

shizhijie

非常感谢啊~~~~~~~~~~~~~