ISO/IEC 18000-3

lovelyjany

【文件名】:08226@52RD_ISO_IEC18000-3_rev2.doc
【格　式】:doc
【大　小】:3277K
【简　介】:Information technology — Radio frequency identification for item management —
Part 3:
Parameters for air interface communications at 13,56 MHz
【目　录】:
Contents Page
Foreword v
Introduction vi
1 Scope 1
2 Conformance 1
2.1 Claiming conformance 1
3 Normative references 1
4 Terms and definitions 2
5 Symbols and abbreviated terms 2
6 Requirements: Physical layer, collision management system and protocol values for 13,56 MHz systems 2
6.0 General and applicable to both Modes of this part of ISO/IEC 18000 2
6.0.1 Presentation as determined in ISO/IEC 18000-1 2
6.0.2 ISO/IEC 18000-3 Interoperability 2
6.0.3 ISO/IEC 18000-3 reader conformance/compliance 3
6.0.4 ISO/IEC 18000-3 tag compliance. 3
6.0.5 Command structure and extensibility 3
6.0.6 Mandatory commands 3
6.0.7 Optional commands 3
6.0.8 Custom commands 3
6.0.9 Proprietary commands 3
6.1 Physical layer, collision management system and protocols for MODE 1 of this part of ISO/IEC 18000 4
6.1.1 Read/Write system 4
6.1.2 Normative Aspects 4
6.1.3 Conformance and performance measurement aspects 4
6.1.4 Physical Layer 4
6.1.5 Protocol and collision management operating method 4
6.1.6 Commands 4
6.1.7 Parameter tables for interrogator to tag link 4
6.1.8 Parameter tables for tag to interrogator link 4
6.1.9 Protocol extension 4
6.1.10 Protocol extension- description of  collision management method 5
6.1.11 Protocol extension commands 14
6.1.12 Air interface application layer 14
6.2 MODE 2: Physical layer, collision management system  and protocols for MODE 2 of this part of ISO/IEC 18000 14
6.2.1 Normative aspects:  physical and media access control (MAC) parameters: interrogator to tag link 14
6.2.2 Tag to interrogator link 14
6.2.3 Description of operating method 14
6.2.4 Protocol parameters 14
6.2.5 Description of protocol operating method 14
6.2.6 Collision management parameters 14
6.2.7 Description of collision management parameters operating method (informative) 14
6.2.8 Tag order sequencing 14
6.2.9 Commands 14
6.2.10 Air interface application layer 14
7 Marking of equipment 14
8 Table of characteristic differences between the MODES specified in this part of ISO/IEC 18000 14
Annex A (normative)  Phase jitter modulation (PJM) 14
Annex B (informative)  Known possible interferences between the MODES determined in this part of ISO/IEC 18000 14
Annex C (informative)  Interrogator pseudo-code for collision management (Mode 1) 14
Annex D (informative)  Cyclic Redundancy Check (CRC) (16 bit) 14
D.1 The CRC error detection method 14
D.2 CRC calculation example 14
Annex E (informative)  Cyclic redundancy check (CRC) mode 2 (32 bit) 14
E.1 The CRC 32 error detection method 14
E.2 CRC 32 calculation example 14
E.3 Practical example of CRC 32 calculation 14
Annex F (informative)  Mode 1 IC reference 14
Annex G (informative)  A description of ISO/IEC 15693 Protocol as used in MODE 1 14
G.1 Parameter tables for interrogator to tag link 14
G.2 Parameter tables for tag to interrogator link 14
G.3 Description of operating method 14
G.3.1 Communications signal interface interrogator to tag 14
G.3.2 Modulation 14
G.3.3 Data rate and data coding 14
G.3.4 Interrogator to tag frames 14
G.3.5 Communications signal interface tag to interrogator 14
G.4 Protocol parameters 14
G.4.1 Table of protocol parameters 14
G.5 Description of protocol operating method 14
G.5.1 Definition of data elements 14
G.5.2 Data storage format identifier (DSFID) 14
G.5.3 CRC 14
G.5.4 Overall protocol description 14
G.5.5 Modes 14
G.5.6 Response format 14
G.5.7 RF tag states 14
G.6 Collision management 14
G.7 Description of collision management operating method (Informative) 14
G.7.1 Request parameters 14
G.7.2 Request processing by the RF tag 14
G.7.3 Explanation of a collision management sequence 14
G.7.4 Timing specifications 14
G.8 Commands 14
G.8.1 Command types 14
G.8.2 Command codes 14
G.8.3 Mandatory commands 14
G.8.4 Optional commands 14
G.8.5 Custom commands 14
G.8.6 Proprietary commands 14
Bibliography 14





目录里面的页码不准确，实际上有154页

xinxinxuezi

狂晕，还要钱[em07]

chtwo

正需要, 谢谢了, 要是中文版就更好了.

What's The Current Job Market For Pornstar Kayleigh Wanless
Professionals Like? pornstar Kayleigh wanless (telegra.Ph)